{"id":2314,"date":"2026-05-20T01:31:48","date_gmt":"2026-05-20T01:31:48","guid":{"rendered":"https:\/\/theinsulatedglass.com\/?p=2314"},"modified":"2026-05-20T01:32:59","modified_gmt":"2026-05-20T01:32:59","slug":"edge-deletion-for-custom-coated-glass-when-it-matters-most","status":"publish","type":"post","link":"https:\/\/theinsulatedglass.com\/ru\/edge-deletion-for-custom-coated-glass-when-it-matters-most\/","title":{"rendered":"\u0423\u0434\u0430\u043b\u0435\u043d\u0438\u0435 \u043a\u0440\u043e\u043c\u043a\u0438 \u0434\u043b\u044f \u0441\u0442\u0435\u043a\u043b\u0430 \u0441 \u0438\u043d\u0434\u0438\u0432\u0438\u0434\u0443\u0430\u043b\u044c\u043d\u044b\u043c \u043f\u043e\u043a\u0440\u044b\u0442\u0438\u0435\u043c: \u041a\u043e\u0433\u0434\u0430 \u044d\u0442\u043e \u043d\u0430\u0438\u0431\u043e\u043b\u0435\u0435 \u0432\u0430\u0436\u043d\u043e"},"content":{"rendered":"

That is precisely why purchasers miss it, fabricators underquote it, and project supervisors uncover it just after the shielded glass unit begins showing ugly perimeter staining, fogging, or a silent seal failure that nobody wants to have. We like to talk about finishes, U-factor, SHGC, argon, krypton, silver layers, warm-edge spacers, robot cutters, and imported tempering lines– yet the slim strip at the border often decides whether the whole device behaves like crafted glass or pricey scrap.<\/p>\n\n\n\n

So why does this little band issue so much?<\/p>\n\n\n\n

Side removal is the regulated elimination of layer from the perimeter of customized coated glass so sealers bond to clean glass rather than delicate metal or oxide coating layers. In simple language: when low-E or various other soft coatings are hidden inside a protected glass system, the edge has to frequently be removed so moisture, acids, sealer stress, and finish corrosion do not gang up at the weakest point.<\/p>\n\n\n\n

I’ll be blunt. In custom layered glass, side deletion is not “added handling.” It is insurance coverage against poor chemistry.<\/p>\n\n\n\n

\"\u0414\u0432\u0443\u0445\u0441\u043b\u043e\u0439\u043d\u043e\u0435<\/figure>\n\n\n\n

The Hard Fact: Coatings Offer the Glass, Edges Kill the Glass<\/h2>\n\n\n\n

Low-E coverings are marketed like magic: far better convenience, reduced warmth transfer, improved solar control, cleaner energy numbers. Some of that is fair. The United State Department of Power states home windows are in charge of about 10% of structure energy use and impact end uses that make up 40% of building energy use, which clarifies why engineers maintain pushing high-performance glazing harder yearly.<\/p>\n\n\n\n

Yet layered glass has a filthy little weak point. The covering pile is slim, metal, and chemically vulnerable at the revealed side.<\/p>\n\n\n\n

Most soft-coat low-E glass uses nanoscale layers that may consist of silver, dielectric oxides, barrier layers, and adhesion layers. Great in the secured cavity. Not wonderful when wetness and side seal chemistry beginning working on it. Cardinal’s technical notice on sputtered Lo\u0112 finishes reported that non-edge-deleted double-silver low-E samples subjected to 140 \u00b0 F, 100% family member humidity, and UV light showed visible silver rust after 4 weeks; the same notice claims edge-deleted examples checked for one year revealed no layer degradation and the IGU seal stayed undamaged.<\/p>\n\n\n\n

That should make any type of glazing customer sit up.<\/p>\n\n\n\n

4 weeks versus one year is not a “minor procedure choice.” It is the distinction in between a spec created by someone who understands area failing and a requirements composed by somebody buying by square-meter price.<\/p>\n\n\n\n

What Side Deletion In Fact Does<\/h2>\n\n\n\n

Edge deletion eliminates the finishing from the perimeter zone where the spacer, primary sealer, and additional sealant demand to bond. The size varies by system, yet several IGU stores operate in the harsh variety of 8– 15 mm relying on spacer depth, sealant bite, layer type, devices tolerance, and last system style.<\/p>\n\n\n\n

The goal is basic: reveal raw glass.<\/p>\n\n\n\n

Raw glass offers the seal system a much better opportunity. Covering layers do not. When the main seal is polyisobutylene, or PIB, and the secondary seal is silicone, polysulfide, or polyurethane, the side bond must tolerate thermal biking, humidity, UV exposure near the border, transport resonance, pressure adjustments, and incomplete installment practices. And yes, imperfect setup is regular. We can claim or else, however the jobsite constantly wins.<\/p>\n\n\n\n

If you are sourcing \u0421\u0442\u0435\u043a\u043b\u043e \u0441 \u0430\u043d\u0442\u0438\u0431\u043b\u0438\u043a\u043e\u0432\u044b\u043c \u043f\u043e\u043a\u0440\u044b\u0442\u0438\u0435\u043c \u043f\u043e \u0438\u043d\u0434\u0438\u0432\u0438\u0434\u0443\u0430\u043b\u044c\u043d\u043e\u043c\u0443 \u0437\u0430\u043a\u0430\u0437\u0443<\/a> for display walls, retail shops, museums, laboratories, or costs interiors, the same logic applies: the finishing system and the edge condition should be discussed with each other, not priced as 2 different globes.<\/p>\n\n\n\n

\"Supplier<\/figure>\n\n\n\n

When Side Removal Issues A Lot Of<\/h2>\n\n\n\n

Edge deletion matters most when the coating gets to the covered boundary of a shielded glass system, especially with soft-coat low-E glass, double-silver low-E, triple-silver low-E, and coated glass revealed to humid or chemically aggressive problems.<\/p>\n\n\n\n

That is the clean answer.<\/p>\n\n\n\n

The untidy answer is much better: side deletion matters when the failure setting is pricey, slow-moving, and politically awful. No one wishes to clarify to a hotel proprietor why 800 IGUs have perimeter haze after the exterior guarantee disagreement has actually currently started.<\/p>\n\n\n\n

Here are the cases where I would certainly press hard for it.<\/p>\n\n\n\n

Low-E Insulated Glass Units<\/h3>\n\n\n\n

Low-E glass side removal is essential in IGUs due to the fact that moisture breach, gas loss, and covering deterioration are attached failures, not different mishaps. NFRC’s consumer advice says IG seal failing can lead to insulating gas loss and condensation between panes, which can break down low-E coatings; it likewise keeps in mind that well-fabricated IG systems can keep gas at much less than 1% loss each year.<\/p>\n\n\n\n

That “well-fabricated” expression is doing a lot of work.<\/p>\n\n\n\n

A system with costs finishing but lazy side prep is not premium. It is a dressed-up danger.<\/p>\n\n\n\n

Double-Silver and Triple-Silver Coatings<\/h3>\n\n\n\n

The even more complicated the finishing pile, the less I rely on the edge unless it has been appropriately deleted. Double-silver and triple-silver low-E finishes provide outstanding solar and thermal efficiency, however silver is not forgiving when revealed to moisture and responsive chemistry.<\/p>\n\n\n\n

This is where low-cost bids obtain dangerous. A provider can quote custom-made coated glass at an appealing rate by missing edge removal, narrowing quality assurance, or assuming the downstream IGU maker will “handle it.” After that the IGU maker assumes the finish supplier already managed it. Lovely. Everybody saves cash till the side transforms brownish.<\/p>\n\n\n\n

Damp, Coastal, Pool, Shower, and Skylight Conditions<\/h3>\n\n\n\n

Water holds your horses.<\/p>\n\n\n\n

In high-humidity areas, edge deletion becomes more than a window-factory information. Think shower enclosures, swimming pool fa\u00e7ades, coastal buildings, skylights, greenhouse roof covering glass, and cozy environments where vapor stress does not take holidays. For restroom or spa jobs, pairing layered or personal privacy glass with a practical edge strategy is particularly crucial; customers considering personal privacy alternative switchable shower wise glass<\/a> must be asking how the glass edge, lamination edge, wiring route, and seal direct exposure are dealt with.<\/p>\n\n\n\n

Skylights are entitled to special suspicion. Warm, UV, ponding water, sealer movement, slope, and installment mistakes concentrate penalty at the border. If the requirements consists of decorative or solar-control glazing, I would rather talk about edge deletion prior to production than fight about leakage after tenancy. That is especially true for bulk silk-screen ceramic frit glass for skylights<\/a>, where frit, finishing, warm treatment, and seal compatibility need to be collaborated as opposed to treated as separated line products.<\/p>\n\n\n\n

Large Custom Glass<\/h3>\n\n\n\n

Big glass relocates a lot more. It bends more. It scares installers more.<\/p>\n\n\n\n

Huge IGUs with custom-made layers are much more at risk to edge anxiety since the border brings the seal tons while the glass experiences temperature level slopes, wind lots, transport stress, suction cup handling, and structure pressure. Side removal will not take care of negative structural layout. Yet without it, the sealant may be bonding to a finish layer that was never ever meant to be the structural or moisture-control user interface.<\/p>\n\n\n\n

\"Supplier<\/figure>\n\n\n\n

When Side Deletion May Not Matter<\/h2>\n\n\n\n

Edge deletion is not immediately required for every item of custom-made coated glass. That is the component some suppliers stay clear of claiming due to the fact that procedure attachments are profitable.<\/p>\n\n\n\n

If the finish is a tough pyrolytic covering developed to survive exposed-edge conditions, side removal might be unnecessary. If the glass is monolithic, not sealed into an IGU, and the side is polished or mounted in a dry interior environment, the risk profile adjustments. If the covering is totally protected by lamination and not in the seal get in touch with area, removal may not be the determining aspect.<\/p>\n\n\n\n

Yet.<\/p>\n\n\n\n

Do not think. Verify the covering type, finish surface, edge exposure, IGU building and construction, and sealant compatibility. A “coated glass” label informs you practically absolutely nothing. Soft layer, hard layer, anti-reflective covering, ceramic frit, conductive finish, mirror covering, and privacy-film settings up all behave in different ways at the side.<\/p>\n\n\n\n

For indoor attractive applications such as custom-cut patterned shower glass<\/a> \u0438\u043b\u0438 custom-cut colored shower screen glass<\/a>, the discussion changes from IGU gas retention to dampness direct exposure, edge ending up, coating sturdiness, cleaning chemicals, and whether the finishing or treatment remains on a vulnerable surface area.<\/p>\n\n\n\n

The Edge Removal Refine: What Takes Place on the<\/h2>\n\n\n\n

The covered lite is normally refined prior to IGU setting up. Relying on the line, glass coating elimination may be done by grinding wheels, unpleasant belts, automated deletion heads, CNC-controlled systems, or specialized edge removal devices incorporated into IGU production.<\/p>\n\n\n\n

Below is the fundamental circulation:<\/p>\n\n\n\n

    \n
  1. Recognize the layered surface area, often surface # 2 or # 3 in a double-glazed IGU.<\/li>\n\n\n\n
  2. Validate deletion width based upon spacer and seal design.<\/li>\n\n\n\n
  3. Get rid of the finish at the border without damaging glass or overheating the edge.<\/li>\n\n\n\n
  4. Evaluate for incomplete deletion, scrapes, finishing residue, and side issues.<\/li>\n\n\n\n
  5. Laundry the glass completely prior to spacer application and securing.<\/li>\n\n\n\n
  6. Construct the IGU with suitable sealers and regulated stress.<\/li>\n<\/ol>\n\n\n\n

    \u041a\u0430\u0436\u0435\u0442\u0441\u044f, \u0447\u0442\u043e \u0432\u0441\u0435 \u043f\u0440\u043e\u0441\u0442\u043e. \u041d\u043e \u044d\u0442\u043e \u043d\u0435 \u0442\u0430\u043a.<\/p>\n\n\n\n

    I have a solid point of view here: edge removal high quality must be inspected like a seal-system variable, not like a cosmetic wipe-down. If residue stays under the PIB line, the device does not care that the billing says “side removed.” Chemistry does not review paperwork.<\/p>\n\n\n\n

    Data Table: When to Specify Edge Deletion<\/h2>\n\n\n\n
    Glass or Task Condition<\/th>Edge Deletion Recommendation<\/th>\u041f\u043e\u0447\u0435\u043c\u0443 \u044d\u0442\u043e \u0432\u0430\u0436\u043d\u043e<\/th>Threat If Neglected<\/th><\/tr><\/thead>
    Soft-coat low-E IGU<\/td>\u0414\u0430<\/td>Protects seal bond and gets rid of susceptible metallic layer from the boundary<\/td>Silver corrosion, delamination, fogging, seal failing<\/td><\/tr>
    Double-silver or triple-silver low-E<\/td>\u0414\u0430<\/td>More intricate finish stacks are extra delicate at revealed sides<\/td>Border staining, aesthetic blockage, warranty conflicts<\/td><\/tr>
    Hard-coat pyrolytic low-E<\/td>Occasionally<\/td>Some difficult finishes tolerate direct exposure better<\/td>Unneeded cost if defined blindly<\/td><\/tr>
    Monolithic layered indoor glass<\/td>Case by case<\/td>No gas tooth cavity or IGU seal, however covering direct exposure still matters<\/td>Edge discoloration, cleaning up damage, inadequate looks<\/td><\/tr>
    Shower, pool, medspa, seaside glass<\/td>Usually yes if layer enters seal or damp side zone<\/td>Wetness and cleansing chemicals elevate rust threat<\/td>Side haze, layer assault, customer issues<\/td><\/tr>
    Skylight IGU<\/td>Yes for soft-coat systems<\/td>Warm, UV, slope, and moisture penalize border seals<\/td>Premature IGU failure<\/td><\/tr>
    Decorative frit-only toughened up glass<\/td>Generally except frit alone<\/td>Ceramic frit is integrated during warm therapy<\/td>Incorrect process added without advantage<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n

    The Price Argument Is Generally In Reverse<\/h2>\n\n\n\n

    I hear this constantly: “Can we avoid edge removal to reduce price?”<\/p>\n\n\n\n

    Incorrect concern.<\/p>\n\n\n\n

    The far better concern is: “What is the substitute expense of one fell short personalized IGU after installation?” Consist of accessibility tools, labor, breakage threat, tenant disturbance, resort area downtime, exterior contractor disagreements, and online reputation damages. Currently compare that to a slim border process done prior to setting up.<\/p>\n\n\n\n

    ENERGY STAR says qualified home windows, doors, and skylights can decrease heating and cooling energy costs by approximately as much as 13% nationwide compared with non-certified products, and its existing residential windows, doors, and skylights specification ended up being efficient on October 23, 2023. That market pressure pushes a lot more projects towards higher-performing covered glass. Greater performance means a lot more coverings. Even more finishes mean more edge choices.<\/p>\n\n\n\n

    This is the cycle no one leaves.<\/p>\n\n\n\n

    A 2023 MDPI review on IGU degradation reported that seal failure and gas loss can boost an IGU’s U-factor by as much as 32%, and substitute heating need increases over two decades rose to 65 MWh for a common office complex under gas concentration loss presumptions. That is not a little spread sheet mistake. That is building-performance drift.<\/p>\n\n\n\n

    \"Supplier<\/figure>\n\n\n\n

    Edge Deletion and Custom-made Coated Glass Specifications<\/h2>\n\n\n\n

    A significant purchase order need to not just say “low-E glass.”<\/p>\n\n\n\n

    It ought to specify covering kind, covering surface, IGU build-up, removal size, spacer type, sealant kind, gas fill, glass density, heat treatment, edge surface, noticeable light transmission, U-factor, SHGC, and assessment requirements.<\/p>\n\n\n\n

    For instance:<\/p>\n\n\n\n

    “6 mm tempered soft-coat low-E on surface # 2\/ 12A argon\/ 6 mm solidified clear, warm-edge spacer, PIB main seal, silicone secondary seal, edge removal 10 mm minimum continual perimeter, no noticeable layer deposit under seal line.”<\/p>\n\n\n\n

    That is a real specification. “Low-E IGU, best rate” is a problem waiting to occur.<\/p>\n\n\n\n

    If the task likewise utilizes wholesale fluted interior design glass<\/a> in adjacent partitions, maintain those ornamental glass packages separate in the schedule. Fluted glass, tinted glass, covered IGUs, wise glass, and fritted skylight glass do not share the same edge threats just because they all get here on racks.<\/p>\n\n\n\n

    Exactly How to Side Erase Coated Glass Without Creating New Problems<\/h2>\n\n\n\n

    The best edge deletion process is monotonous, repeatable, and recorded.<\/p>\n\n\n\n

    The operator needs to validate the covered side prior to removal. The maker ought to remove layer continually without over-grinding the glass side. The deletion band must line up with spacer positioning. The cleaning system needs to get rid of fragments before securing. The QC team should check deletion connection under appropriate lights, not wave the lite with due to the fact that production lags.<\/p>\n\n\n\n

    3 failure patterns show up repeatedly:<\/p>\n\n\n\n

    First, incomplete deletion. A thin deposit line continues to be where the sealant lands.<\/p>\n\n\n\n

    Second, over-aggressive deletion. The machine harms the glass side, raising damage risk.<\/p>\n\n\n\n

    Third, wrong-side removal. Yes, it happens. And it is precisely as unpleasant as it appears.<\/p>\n\n\n\n

    The Purchasing Checklist I Would Use<\/h2>\n\n\n\n

    Ask these before authorizing a custom layered glass order:<\/p>\n\n\n\n

      \n
    • What finish kind is being made use of: soft coat, tough coat, anti-reflective, conductive, ceramic frit, or one more system?<\/li>\n\n\n\n
    • Which glass surface lugs the finish?<\/li>\n\n\n\n
    • Is the coated lite going into an insulated glass system?<\/li>\n\n\n\n
    • What deletion size is required by the covering provider and IGU maker?<\/li>\n\n\n\n
    • What primary and additional sealers are being utilized?<\/li>\n\n\n\n
    • Does the distributor examine for finishing residue after deletion?<\/li>\n\n\n\n
    • Is edge removal included in the priced estimate price or concealed as an optional procedure?<\/li>\n\n\n\n
    • What happens if the last device reveals border rust within the guarantee duration?<\/li>\n<\/ul>\n\n\n\n

      That last inquiry makes weak vendors worried. Great.<\/p>\n\n\n\n

      \u0427\u0410\u0421\u0422\u041e \u0417\u0410\u0414\u0410\u0412\u0410\u0415\u041c\u042b\u0415 \u0412\u041e\u041f\u0420\u041e\u0421\u042b<\/h2>\n\n\n\n

      What is edge removal for personalized coated glass?<\/h3>\n\n\n\n

      Side deletion for customized layered glass is the controlled removal of finishing from the perimeter of a glass lite before sealing, glazing, or insulating glass setting up. It subjects tidy glass so sealants bond effectively and susceptible finish layers are not caught at the edge where wetness, chemicals, and activity strike first.<\/p>\n\n\n\n

      In low-E glass side removal, the purpose is not to make the glass prettier. It is to maintain the metal covering store from the seal course. That matters most in IGUs, where failure can suggest fogging, gas loss, layer deterioration, and a replacement expense that towers over the processing cost.<\/p>\n\n\n\n

      When is edge deletion required?<\/h3>\n\n\n\n

      Edge deletion is required when a soft covered glass surface area gets to the perimeter seal area of a protected glass unit or an additional moisture-sensitive assembly. It is especially advised for low-E IGUs, double-silver coatings, triple-silver coatings, skylights, big exterior devices, and moist applications where subjected covering sides can corrode or flake.<\/p>\n\n\n\n

      The best regulation is this: if the layer is soft, metal, and hidden near a seal, request for side removal unless the finishing supplier states otherwise in creating. Spoken guarantees are low-cost. Fallen short glass is not.<\/p>\n\n\n\n

      Is side deletion needed for all low-E glass?<\/h3>\n\n\n\n

      Edge removal is not needed for all low-E glass since finishing chemistry, finish technique, system building, and direct exposure conditions vary. Soft-coat low-E glass in IGUs generally requires removal, while some hard-coat pyrolytic low-E items may tolerate revealed sides better and might not require the exact same perimeter elimination procedure.<\/p>\n\n\n\n

      The mistake is dealing with “low-E” as one material. It is a classification. A sputtered double-silver soft layer and a pyrolytic difficult coat do not behave similarly at the perimeter.<\/p>\n\n\n\n

      How to border delete covered glass appropriately?<\/h3>\n\n\n\n

      To edge delete covered glass appropriately, recognize the covered surface, established the defined deletion size, remove the coating constantly around the border, evaluate for deposit or glass damages, wash the lite completely, and confirm that the spacer and sealer land only on clean glass rather than layer.<\/p>\n\n\n\n

      Automation aids, yet assessment matters more. A gorgeous removal pass that misses one corner is still a weak point. The process ought to be tied to IGU assembly needs, not dealt with as a different grinding chore.<\/p>\n\n\n\n

      What takes place if low-E glass is not edge erased?<\/h3>\n\n\n\n

      If low-E glass is not border deleted when the design needs it, the subjected finish side can corrode, flake, compromise seal bond, and permit moisture-related failing to move right into the noticeable glass location. In an IGU, this can mean fogging, silver staining, gas loss, minimized thermal performance, and service warranty dispute.<\/p>\n\n\n\n

      The ugly part is timing. The device may pass aesthetic evaluation at delivery. The failing can appear later, after setup, when replacement becomes pricey and everybody begins searching old e-mails.<\/p>\n\n\n\n

      Does side deletion damage glass?<\/h3>\n\n\n\n

      Correct edge deletion should not weaken glass when executed with the proper tools, stress, speed, and evaluation controls. The procedure removes coating from the surface area perimeter as opposed to cutting deeply right into the glass body, so the actual risk originates from inadequate devices arrangement, edge breaking, overheating, or reckless handling.<\/p>\n\n\n\n

      Do decline obscure responses right here. Ask whether the supplier look for side chips, removal size uniformity, and finish residue. The ideal process is regulated. The incorrect process is simply grinding with positive outlook.<\/p>\n\n\n\n

      \u0417\u0430\u043a\u043b\u044e\u0447\u0435\u043d\u0438\u0435<\/h2>\n\n\n\n

      Edge removal is among those manufacturing information that divides significant glass supply from quote-sheet cinema.<\/p>\n\n\n\n

      If your customized coated glass is monolithic, interior, dry, and made with a finishing system that tolerates subjected sides, penalty– do not over-specify. Yet if you are getting soft-coat low-E insulated glass units, skylight IGUs, high-humidity layered settings up, big exterior devices, or costs energy glass, avoiding edge deletion is normally incorrect economic climate with a polished edge.<\/p>\n\n\n\n

      For custom covered glass jobs where finish performance, side sturdiness, personal privacy, solar control, or attractive style all have to line up, start the conversation prior to manufacturing. Share the glass build-up, covering type, attracting, side direct exposure, and last application– and make edge deletion a requirements choice, not a surprise charge.<\/p>","protected":false},"excerpt":{"rendered":"

      \u0423\u0434\u0430\u043b\u0435\u043d\u0438\u0435 \u043a\u0440\u043e\u043c\u043e\u043a - \u044d\u0442\u043e \u043d\u0435 \u043a\u043e\u0441\u043c\u0435\u0442\u0438\u0447\u0435\u0441\u043a\u0438\u0439 \u0448\u0430\u0433; \u044d\u0442\u043e \u0440\u0435\u0448\u0435\u043d\u0438\u0435 \u043f\u043e \u043a\u043e\u043d\u0442\u0440\u043e\u043b\u044e \u0440\u0438\u0441\u043a\u043e\u0432 \u0434\u043b\u044f \u0441\u0442\u0435\u043a\u043b\u0430 \u0441 \u043f\u043e\u043a\u0440\u044b\u0442\u0438\u0435\u043c, \u0438\u0437\u0433\u043e\u0442\u043e\u0432\u043b\u0435\u043d\u043d\u043e\u0433\u043e \u043d\u0430 \u0437\u0430\u043a\u0430\u0437, \u043e\u0441\u043e\u0431\u0435\u043d\u043d\u043e \u0434\u043b\u044f \u0441\u0442\u0435\u043a\u043b\u043e\u043f\u0430\u043a\u0435\u0442\u043e\u0432 \u0441 \u043d\u0438\u0437\u043a\u043e\u044d\u043c\u0438\u0441\u0441\u0438\u043e\u043d\u043d\u044b\u043c \u043f\u043e\u043a\u0440\u044b\u0442\u0438\u0435\u043c. \u0412 \u044d\u0442\u043e\u0439 \u0441\u0442\u0430\u0442\u044c\u0435 \u043e\u0431\u044a\u044f\u0441\u043d\u044f\u0435\u0442\u0441\u044f, \u043a\u043e\u0433\u0434\u0430 \u044d\u0442\u043e \u0438\u043c\u0435\u0435\u0442 \u0437\u043d\u0430\u0447\u0435\u043d\u0438\u0435, \u0430 \u043a\u043e\u0433\u0434\u0430 \u043d\u0435\u0442, \u0438 \u043f\u043e\u0447\u0435\u043c\u0443 \u043d\u0435\u0431\u0440\u0435\u0436\u043d\u0430\u044f \u043e\u0431\u0440\u0430\u0431\u043e\u0442\u043a\u0430 \u043a\u0440\u043e\u043c\u043e\u043a \u043c\u043e\u0436\u0435\u0442 \u043f\u0440\u0435\u0432\u0440\u0430\u0442\u0438\u0442\u044c \u0441\u0442\u0435\u043a\u043b\u043e \u043f\u0440\u0435\u043c\u0438\u0443\u043c-\u043a\u043b\u0430\u0441\u0441\u0430 \u0432 \u043f\u0440\u0435\u0434\u043c\u0435\u0442 \u0441\u043f\u043e\u0440\u0430 \u043f\u043e \u0433\u0430\u0440\u0430\u043d\u0442\u0438\u0438.<\/p>","protected":false},"author":2,"featured_media":2304,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"_gspb_post_css":"","footnotes":""},"categories":[1],"tags":[1302,1301,1303,1304,985,982],"class_list":["post-2314","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-glass-product-innovations-applications","tag-custom-coated-glass","tag-edge-deletion","tag-glass-coating-removal","tag-igu-seal-failure","tag-insulated-glass-unit","tag-low-e-glass"],"blocksy_meta":[],"_links":{"self":[{"href":"https:\/\/theinsulatedglass.com\/ru\/wp-json\/wp\/v2\/posts\/2314","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/theinsulatedglass.com\/ru\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/theinsulatedglass.com\/ru\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/theinsulatedglass.com\/ru\/wp-json\/wp\/v2\/users\/2"}],"replies":[{"embeddable":true,"href":"https:\/\/theinsulatedglass.com\/ru\/wp-json\/wp\/v2\/comments?post=2314"}],"version-history":[{"count":1,"href":"https:\/\/theinsulatedglass.com\/ru\/wp-json\/wp\/v2\/posts\/2314\/revisions"}],"predecessor-version":[{"id":2316,"href":"https:\/\/theinsulatedglass.com\/ru\/wp-json\/wp\/v2\/posts\/2314\/revisions\/2316"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/theinsulatedglass.com\/ru\/wp-json\/wp\/v2\/media\/2304"}],"wp:attachment":[{"href":"https:\/\/theinsulatedglass.com\/ru\/wp-json\/wp\/v2\/media?parent=2314"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/theinsulatedglass.com\/ru\/wp-json\/wp\/v2\/categories?post=2314"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/theinsulatedglass.com\/ru\/wp-json\/wp\/v2\/tags?post=2314"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}